Material Safety Data Sheet

Material Safety Data Sheet

EMERGENCY CONTACTS:
• Spills, Leaks, Fire or Exposure Call Chemtrec: (800) 424-9300
• Medical Emergency Information: (800) 561-3636

Section 1: PRODUCT IDENTIFICATION

TRADE NAME:	RT-5090-60-B
MANUFACTURER'S NAME:	RESIN TECHNOLOGY COMPANY
Telephone:	(909) 947-7224
Address:	2270 Castle Harbor Place Ontario, CA 91761
Date prepared:	07/28/94
Revision Date:	10/31/00

Section 2: HAZARDOUS INGREDIENTS
This product has not been tested as a whole. Information provided in this material safety data sheet is based on the limited knowledge Resin Technology Company has on the component parts of the mixture.

Hazardous Ingredient or Chemical Family	CAS Number	% W/W	ACGIH TLV	OSHA PEL	Other/ Manufacturer
Polyether Polyol	-	20 - 27	None Listed	None Listed	None Listed
Polyurethane Polyol	-	30 - 35	None Listed	None Listed	None Listed
Phosphate Flame Retardant	-	5 - 10	None Listed	None Listed	None Listed
Surfactant	68412-54-4	2 - 4	Not Established	Not Established	Not Established

Section 3: PHYSICAL PROPERTIES

Appearance and odor:	Amber liquid; negligible odor; slightly aromatic
Vapor Density: (air =1)	5.67
Melting Point, °F:	Not Available
Specific Gravity:	1.20
Boiling Point, °F:	82-95 °F
Solubility in Water:	Moderate
Evaporation Rate (butyl acetate=1):	>1
Vapor Pressure: (mm Hg @ 20OC):	Not determined

Section 4: FIRE AND EXPLOSION
Flash Point, °F (Closed Cup): 269°F

Auto ignition temperature, °F: No Data

Flammable limits in air, volume %: No Data lower

Fire extinguishing materials: water spray, carbon dioxide, other: foam, dry chemical

Special firefighting procedures: None Known. However, firefighters should wear self-contained breathing apparatus to avoid inhalation of smoke & vapors.

Unusual fire and explosion hazards: None Known

Section 5: HEALTH HAZARD INFORMATION
HAZARDS IDENTIFICATION
   • HMIS Ratings: Health: 1, Flammability: 1, Reactivity: 0

SYMPTOMS OF OVEREXPOSURE:
   • Inhalation: May be irritating to the lungs and respiratory passages.
   • Eye Contact: Irritation may develop following eye contact.
   • Skin Contact: Irritation may develop following skin contact. Toxic concentrations are unlikely to be absorbed through the skin.
   • Ingestion: Product is slightly toxic by ingestion. Irritation of the gastrointestinal tract may occur following ingestion.

HEALTH EFFECTS OR RISKS FROM EXPOSURE:
   • Acute: None known if concentrations are maintained below TLV levels. Exposure above TLV may result in transient reversible respiratory system and skin irritation, dizziness, difficulty in breathing, and unconsciousness.
   • Chronic: None known.

FIRST AID: EMERGENCY PROCEDURES
   • Eye Contact: Flush immediately with copious amounts of water for at least 15 minutes. CONSULT MEDICAL PERSONNEL IMMEDIATELY.
   • Skin Contact: Flush immediately with water. The affected area should then be washed with soap and water.
   • Inhaled: Remove victim to fresh air. If not breathing, give artificial respiration, preferably by mouth to mouth method. If breathing is labored, give oxygen. CONSULT MEDICAL PERSONNEL.
   • Swallowed: If ingested, induce vomiting and CALL PHYSICIAN AT ONCE.

CARCINOGENICITY: The ingredients in this product are NOT found in the following lists: Federal OSHA, NTP, IARC

This product contains detectable amounts of a chemical known to the state of California to cause cancer, birth defects, or other reproductive harm. (California Health and Safety Code Section 25249.6)

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None known.

Section 6: REACTIVITY DATA
Stability: Stable

Conditions to avoid: High Temperatures.

Incompatibility (materials to avoid): Oxidizing agents; Strong acids; Strong bases; Isocyanates

Hazardous polymerization: Will not occur

Conditions to avoid: None known.

Section 7: SPILL, LEAK AND DISPOSAL PROCEDURES
Spill response procedures (include employee protection measures): Avoid breathing fumes - use adequate fresh air supply.

Preparing wastes for disposal (container types, neutralization, etc.): Spread with absorbent material and shovel into sealable container.

NOTE: Dispose of all wastes in accordance with federal, state and local regulations.

Section 8: SPECIAL HANDLING INFORMATION
Ventilation and engineering controls:
• Outdoors: Close all air intake vents on air handling equipment on buildings.
• Indoors: Use local exhaust if aerosol is generated.

Respiratory protection: Fresh air full face mask or hood with fresh air source.

Eye protection: Safety goggles.

Gloves: Chemically resistant plastic or rubber.

Other clothing and equipment: Fabric coveralls & rubber apron.

Work practices, hygienic practices: Restrict access of non-application personnel.

Other requirements: Store in original containers away from heat & moisture. Store indoors between 50°F and 75°F. Open containers carefully to allow any pressure buildup to be vented safely. Protective measures during maintenance of contaminated equipment: Fabric coveralls, safety goggles, chemically resistant gloves, and fresh air full face mask.

Section 9: REVISION NOTES
Revision By: Chemical Data Management Systems
Revision Date: 10/31/00
Revision No: 1

Return to Material Safety Data Sheets Menu

PERMAX® Roofing Systems | PERMAX® Insulation Systems
Spray Foam Product Guide | Elastomeric Coatings Product Guide
Polyurea Product Guide | Primers Product Guide
Polyurethane Foams Product Guide for OEM Applications
Technical Bulletins | Material Safety Data Sheets
To the RTC Main Page | To the PERMAX® Main Page