Material Safety Data Sheet

      EMERGENCY CONTACTS:
         •     Spills, Leaks, Fire or Exposure Call Chemtrec: (800) 424-9300
         •     Medical Emergency Information: (800) 228-5635 Ext. 181




      SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
      TRADE NAME: NEOPRIME

      RESIN TECHNOLOGY COMPANY
         •     2270 Castle Harbor Place, Ontario, CA 91761
         •     Phone: (800) 729-0795
         •     Fax: (909) 923-9617
         •     DATE OF PREPARATION 8/30/99


      These ratings should be used only as part of fully implemented H.M.I.S. program:

      HEALTH: 1, FLAMMABILITY: 0, REACTIVITY: 0



      SECTION 2 - HAZARDOUS INGREDIENTS
      Contains No Known Hazardous Ingredients



      SECTION 3 - HEALTH INFORMATION
      EFFECTS OF SHORT TERM OVEREXPOSURE

      SWALLOWING: Unknown

      INHALATION: May cause respiratory irritation.

      EYE: May cause transient eye irritation. Liquid splashed into the eye may cause transient eye irritation.

      SKIN: May cause transient skin irritation.

      EFFECTS OF REPEATED OVEREXPOSURE: None currently known.

      SIGNIFICANT LABORATORY DATA WITH POSSIBLE RELEVANCE TO HUMAN HEALTH: None currently known.



      SECTION 4 - FIRST AID AND EMERGENCY PROCEDURES
      SWALLOWING: If swallowed call Poison Control Center, Hospital Emergency Room, or Physician immediately.

      INHALATION: Remove to fresh air.

      EYE: Flush with large amounts of water, lifting upper and lower lids occasionally. Continue for at least 15 minutes. Get medical attention.

      SKIN: Remove contaminated clothing. Wash affected area with soap and water. Obtain medical attention if irritation persists.

      NOTES TO PHYSICIAN: Any treatment that might be required for overexposure should be directed at the control of symptoms and the clinical conditions.



      SECTION 5 – FIRE-FIGHTING MEASURES
      NFPA FLAMMABILITY CLASSIFICATION: Not Applicable

      FLASHPOINT: Not Applicable

      EXTINGUISHING MEDIA: Will not burn

      UNUSUAL FIRE AND EXPLOSION HAZARDS: None known

      SPECIAL FIRE FIGHTING PROCEDURES: None known



      SECTION 6 – ACCIDENTAL RELEASE MEASURES
      STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Confine in small area; use absorbent to clean up. Place in container for disposal.

      WASTE DISPOSAL: Dispose in accordance with federal, state and local regulations.

      ENVIRONMENTAL HAZARDS: None known



      SECTION 7 – HANDLING AND STORAGE
      PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Protect from freezing.

      OTHER PRECAUTIONS: Do not take internally. Close container after each use. Keep away from children



      SECTION 8 – EXPOSURE CONTROLS
      RESPIRATORY PROTECTION: If applied by spraying, use an appropriate, properly fitted NIOSH/MSHA approved respirator to remove the spray mist. Refer to OSHA 29 CFR 1910.134 "Respiratory Protection".

      VENTILATION: Natural ventilation should be adequate under normal conditions.

      HAND PROTECTION: Not likely to be needed.

      EYE PROTECTION: Wear safety spectacles with side shields. Wear face shield as necessary when spraying.

      OTHER PROTECTIVE EQUIPMENT: Not likely to be needed.



      SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES
      BOILING RANGE: 139°F (59°C) to 212°F (100°C)

      VAPOR DENSITY: Heavier than air.

      % VOLATILE BY VOLUME: 56

      EVAPORATION RATE: Slower than diethyl ether.

      VOC .21 LB/GAL LESS WATER & NPRS* 25 G/L LESS WATER CALCULATED

      WEIGHT LB/GAL 8.9 VOC .21 LB/GAL SOLIDS 25 G/L SOLIDS CALCULATED

      SPECIFIC GRAVITY: 1.1

      All physical data determined at 68°F (20°C) 760 mm Hg

      *Negligibly Photochemically Reactive Materials



      SECTION 10 – STABILITY AND REACTIVITY
      STABILITY: Normally stable.

      CONDITIONS TO AVOID: None known.

      INCOMPATIBILITY (MATERIALS TO AVOID): None known.

      HAZARDOUS DECOMPOSITION PRODUCTS: Burning, including when heated by welding or cutting, will produce smoke, carbon monoxide and carbon dioxide.

      HAZARDOUS POLYMERIZATION: Will not occur.

      CONDITIONS TO AVOID: None known.



      SECTION 11 – TOXICOLOGICAL INFORMATION
      No information available.



      SECTION 12 – ECOLOGICAL INFORMATION
      No information available.



      SECTION 13 – DISPOSAL CONSIDERATION
      See Section 6.



      SECTION 14 – TRANSPORT INFORMATION
      MODE PROPER SHIPPING NAME CLASS I.D.# PKG GRP
      IATA (AIR) ADHESIVES, NOT RESTRICTED FREEZABLE DOT (HM-181)
      (DOMESTIC SURFACE) ADHESIVES, NOT REGULATED FREEZABLE IMDG CODE
      (OCEAN) ADHESIVES, NOT RESTRICTED -




      SECTION 15 – REGULATORY INFORMATION
      No information available.



      SECTION 16 – OTHER INFORMATION THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED TO BE ACCURATE. WHILE THE INFORMATION IS BELIEVED TO BE RELIABLE, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THIS DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. SINCE THE USE OF THIS INFORMATION AND THE CONDITIONS AND USE OF THIS PRODUCT ARE CONTROLLED BY THE USER, IT IS THE USER'S OBLIGATION TO DETERMINE THE CONDITIONS OF SAFE USE OF THE PRODUCT.

      The Corporate Safety and Environmental Affairs Department is responsible for the preparation of this Material Safety Data Sheet.

      Return to Material Safety Data Sheets Menu

    PERMAX® Roofing Systems  |  PERMAX® Insulation Systems
    Spray Foam Product Guide  |  Elastomeric Coatings Product Guide
    Polyurea Product Guide  |  Primers Product Guide
    Polyurethane Foams Product Guide for OEM Applications
    Technical Bulletins   |  Material Safety Data Sheets
    To the RTC Main Page |  To the PERMAX® Main Page
    Contact Info
    ©1997 Resin Technology Company. All Rights Reserved.
    click here for the copyright terms of use

    This website designed and maintained by DigiTeel.